Difference between revisions of "RSA Registers"
Jump to navigation
Jump to search
| Line 54: | Line 54: | ||
|- | |- | ||
| 8-9 | | 8-9 | ||
| − | | Should be set to 0x3 before accessing REG_RSATXT and | + | | Should be set to 0x3 before accessing REG_RSATXT and REG_RSAMOD |
|} | |} | ||
| Line 99: | Line 99: | ||
== REG_RSAEXPFIFO == | == REG_RSAEXPFIFO == | ||
| − | The 0x100-byte exponent is written to this write-only FIFO. | + | The 0x100-byte private or public exponent is written to this write-only FIFO. |
| − | == | + | == REG_RSAMOD == |
| − | The RSA | + | The RSA key modulo for the selected keyslot can be written here. When writing the RSA modulo, the modulo must align with the end of the register area. |
== REG_RSATXT == | == REG_RSATXT == | ||
Revision as of 22:53, 14 August 2012
Registers
| NAME | PHYSICAL ADDRESS | WIDTH |
|---|---|---|
| REG_RSACNT | 0x1000B000 | 0x04 |
| REG_RSASLOT0 | 0x1000B100 | 0x10 |
| REG_RSASLOT1 | 0x1000B110 | 0x10 |
| REG_RSASLOT2 | 0x1000B120 | 0x10 |
| REG_RSASLOT3 | 0x1000B130 | 0x10 |
| REG_RSAEXPFIFO | 0x1000B200 | 0x04 |
| REG_RSAMOD | 0x1000B400 | 0x100 |
| REG_RSATXT | 0x1000B800 | 0x100 |
REG_RSACNT
| Bit | Description |
|---|---|
| 0 | Start (1=Enable/Busy, 0=Idle) |
| 1 | Encrypt/Decrypt |
| 4-7 | Keyslot |
| 8-9 | Should be set to 0x3 before accessing REG_RSATXT and REG_RSAMOD |
REG_RSASLOT
| Start | Width | Description |
|---|---|---|
| 0x0 | 0x4 | REG_RSASLOTCNT |
| 0x4 | 0x4 | REG_RSASLOTSIZE |
| 0x8 | 0x4 | ? |
| 0xC | 0x4 | ? |
REG_RSASLOTCNT
| Bits | Description |
|---|---|
| 0 | Key status (1=Key has been set, 0=Key has not been set yet) |
| 1 | Key write-protect |
| 31-2 | ? |
REG_RSASLOTSIZE
This contains the RSA size for this slot, in words. Normally this is 0x40 for RSA-2048.
REG_RSAEXPFIFO
The 0x100-byte private or public exponent is written to this write-only FIFO.
REG_RSAMOD
The RSA key modulo for the selected keyslot can be written here. When writing the RSA modulo, the modulo must align with the end of the register area.
REG_RSATXT
The RSA signature can be written here, and the data read from here is the message. When writing the RSA signature, the signature must be prepended with zeroes until it is a multiple of 8 bytes, and the end of the signature must align with the end of the register area.
The PKCS message padding must be manually checked by software, as hardware will only do raw RSA operations.
Keyslots usage
| Keyslot | Description |
|---|---|
| 0 | Arbitrary |
| 1 | CXI access desc (following the exheader) |
| 2-3 | Unused |