IRU:SetBitRate: Difference between revisions
Created page with "=Request= {| class="wikitable" border="1" |- ! Index Word ! Description |- | 0 | Header code [0x00090040] |- | 1 | u8 bitrate value |} =Response= {| class="wikitable" border="..." |
|||
| (3 intermediate revisions by the same user not shown) | |||
| Line 30: | Line 30: | ||
|- | |- | ||
! Value | ! Value | ||
! | ! Converted divisor value | ||
! Bits-per-second / description | ! Bits-per-second / description | ||
|- | |- | ||
| 3 | | 3 | ||
| 10 | | 10 | ||
| | | 115200 | ||
|- | |- | ||
| 4 | | 4 | ||
| 12 | | 12 | ||
| | | 96000 | ||
|- | |- | ||
| 5 | | 5 | ||
| 16 | | 16 | ||
| | | 72000 | ||
|- | |- | ||
| 6 | | 6 | ||
| 24 | | 24 | ||
| | | 48000 (This is the default for IRU) | ||
|- | |- | ||
| 7 | | 7 | ||
| 32 | | 32 | ||
| | | 36000 | ||
|- | |- | ||
| 8 | | 8 | ||
| 48 | | 48 | ||
| | | 24000 | ||
|- | |- | ||
| 9 | | 9 | ||
| 64 | | 64 | ||
| | | 18000 | ||
|- | |- | ||
| 10 | | 10 | ||
| 96 | | 96 | ||
| | | 12000 | ||
|- | |- | ||
| 11 | | 11 | ||
| 120 | | 120 | ||
| | | 9600 | ||
|- | |- | ||
| 12 | | 12 | ||
| 192 | | 192 | ||
| | | 6000 | ||
|- | |- | ||
| 13 | | 13 | ||
| 384 | | 384 | ||
| | | 3000 | ||
|- | |- | ||
|- | |- | ||
| 14 | | 14 | ||
| 20 | | 20 | ||
| | | 57600 | ||
|- | |- | ||
| 15 | | 15 | ||
| 30 | | 30 | ||
| | | 38400 | ||
|- | |- | ||
| 16 | | 16 | ||
| 60 | | 60 | ||
| | | 19200 | ||
|- | |- | ||
| 17 | | 17 | ||
| 160 | | 160 | ||
| | | 7200 | ||
|- | |- | ||
| 18 | | 18 | ||
| 240 | | 240 | ||
| | | 4800 | ||
|} | |} | ||
The bps listed above is from code in IR module which converts the input value into actual bps, that function is only used with delay code however. | |||
The converted value is the following(from a datasheet): "16-bit divisor for generation of the baud clock in the baud rate generator". The baud/bit rate is calculated with the following, where clk is 1152000: bitrate = clk / divisor. | |||
=Description= | =Description= | ||
This sets the current bitrate. Error 0xE0E10FED is returned when the input value is outside of the above range. Error 0xF9610C02 is returned when the I2C code returns an error. | This sets the current bitrate. Error 0xE0E10FED is returned when the input value is outside of the above range. Error 0xF9610C02 is returned when the I2C code returns an error. | ||