Difference between revisions of "RSA Registers"
m ("modulus" is the correct Latin case here.) |
|||
Line 127: | Line 127: | ||
== REG_RSAMOD == | == REG_RSAMOD == | ||
− | The RSA key | + | The RSA key modulus for the selected keyslot can be written here. When writing the RSA modulus, the modulus must align with the end of the register area. |
== REG_RSATXT == | == REG_RSATXT == |
Revision as of 01:38, 8 March 2016
Registers
Old3DS | Name | Address | Width | Used by |
---|---|---|---|---|
Yes | RSA_CNT | 0x1000B000 | 0x04 | |
Yes | RSA_SLOT0 | 0x1000B100 | 0x10 | |
Yes | RSA_SLOT1 | 0x1000B110 | 0x10 | |
Yes | RSA_SLOT2 | 0x1000B120 | 0x10 | |
Yes | RSA_SLOT3 | 0x1000B130 | 0x10 | |
Yes | RSA_EXPFIFO | 0x1000B200 | 0x04 | |
Yes | RSA_MOD | 0x1000B400 | 0x100 | |
Yes | RSA_TXT | 0x1000B800 | 0x100 |
RSA_CNT
Bit | Description |
---|---|
0 | Start (1=Enable/Busy, 0=Idle) |
1 | ? |
4-7 | Keyslot (Bit6-7 don't actually affect the keyslot) |
8 | Endianness (1=Little endian, 0=Big endian) |
9 | Word order (1=Normal order, 0=Reversed order) |
RSA_SLOT
Start | Width | Description |
---|---|---|
0x0 | 0x4 | REG_RSASLOTCNT |
0x4 | 0x4 | REG_RSASLOTSIZE |
0x8 | 0x4 | ? |
0xC | 0x4 | ? |
RSA_SLOTCNT
Bits | Description |
---|---|
0 | Key status (1=Key has been set, 0=Key has not been set yet) |
1 | Key write-protect, this bit is RW. (0 = no protection, 1 = protected) |
30-2 | ? |
31 | ? |
Before writing RSA_EXPFIFO/RSA_MOD, bit0 here should be cleared when bit31 is already clear. Otherwise, the ARM9 will hang when attempting to write to RSA_EXPFIFO.
RSA_SLOTSIZE
This contains the RSA size for this slot, in words. Normally this is 0x40 for RSA-2048.
RSA_EXPFIFO
The 0x100-byte private or public exponent is written to this write-only FIFO.
REG_RSAMOD
The RSA key modulus for the selected keyslot can be written here. When writing the RSA modulus, the modulus must align with the end of the register area.
REG_RSATXT
The RSA signature can be written here, and the data read from here is the message. When writing the RSA signature, the signature must be prepended with zeroes until it is a multiple of 8 bytes, and the end of the signature must align with the end of the register area.
The PKCS message padding must be manually checked by software, as hardware will only do raw RSA operations.
Keyslots usage
Keyslot | Description |
---|---|
0 | Arbitrary |
1 | CXI access desc (following the exheader) |
2-3 | Initialized by the ARM9 bootrom, but not used by any of the FIRMs. It's unknown what the ARM9 bootrom uses these for, if anything. |