Config Services

These commands are common to all Config services, except for "cfg:nor".

Command Header Available since system version Description
0x00010082 GetConfigInfoBlk2
0x00020000 SecureInfoGetRegion
0x00030040 GenHashConsoleUnique/GetTransferableId
0x00040000 3.0.0-5 GetRegionCanadaUSA/IsCoppacsSupported
0x00050000 5.0.0-11 GetSystemModel
0x00060000 6.0.0-11 GetModelNintendo2DS
0x00070040 7.0.0-13 (u8 val) This writes the input u8 to the first byte in the config-block for blkID 0x00160000.
0x00080080 7.0.0-13 TranslateCountryInfo
0x00090040 7.0.0-13 GetCountryCodeString
0x000A0040 7.0.0-13 GetCountryCodeID
0x000B0000 9.3.0-X IsFangateSupported

Config service "cfg:u"

This service provides no new commands in addition to the common ones.

Config service "cfg:s"

Command Header Available since system version Description
0x00050000 Same as cfg:u 0x00050000 cmd?
0x04010082 GetConfigInfoBlk8
0x04020082 SetConfigInfoBlk4
0x04030000 UpdateConfigNANDSavegame
0x04040042 GetLocalFriendCodeSeedData
0x04050000 GetLocalFriendCodeSeed
0x04060000 SecureInfoGetRegion
0x04070000 SecureInfoGetByte101
0x04080042 SecureInfoGetSerialNo
0x04090000 UpdateConfigBlk00040003
0x040A0000 ? ?
0x040B0000 ? ?
0x040C0000 ? ?
0x040D0040 ? ?
0x040E0000 ? ?
0x040F0000 ? ?

CfgS command 0x04060000(SecureInfoGetRegion) is used by NIM module to determine the SOAP RegionId, when sending SOAP requests. See here.

Config service "cfg:i"

Command Header Available since system version Description
0x04010082 GetConfigInfoBlk8
0x04020082 SetConfigInfoBlk4
0x04030000 UpdateConfigNANDSavegame
0x04040042 GetLocalFriendCodeSeedData
0x04050000 GetLocalFriendCodeSeed
0x04060000 SecureInfoGetRegion
0x04070000 SecureInfoGetByte101
0x04080042 SecureInfoGetSerialNo
0x04090000 UpdateConfigBlk00040003
0x040A0000 ? ?
0x040B0000 ? ?
0x040C0000 ? ?
0x040D0040 ? ?
0x040E0000 ? ?
0x040F0000 ? ?
0x08010082 GetConfigInfoBlk8
0x08020082 SetConfigInfoBlk4
0x08030000 UpdateConfigNANDSavegame
0x080400C2 CreateConfigInfoBlk
0x08050000 DeleteConfigNANDSavefile
0x08060000 FormatConfig
0x08070000 This basically just returns result-code value 0x0, due to code this eventually executes being NOPed out.
0x08080000 This updates the config blocks for blkIDs 0x0 and 0x20000. In certain cases this may call the code for FormatConfig.
0x08090000 This updates the config block for blkID 0x60000.
0x080A0000 ResetAnalogStickCalibrationParam? This updates the config block for blkID 0x00040001.
0x080B0082 SetGetLocalFriendCodeSeedData
0x080C0042 SetLocalFriendCodeSeedSignature
0x080D0000 DeleteCreateNANDLocalFriendCodeSeed
0x080E0000 VerifySigLocalFriendCodeSeed
0x080F0042 GetLocalFriendCodeSeedData
0x08100000 GetLocalFriendCodeSeed
0x08110084 SetSecureInfo
0x08120000 DeleteCreateNANDSecureInfo
0x08130000 VerifySigSecureInfo
0x08140042 SecureInfoGetData
0x08150042 SecureInfoGetSignature
0x08160000 SecureInfoGetRegion
0x08170000 SecureInfoGetByte101
0x08180042 SecureInfoGetSerialNo
0x0819.... ? ?
0x081A.... ? ?
0x081B.... ? ?
0x081C.... ? ?
0x081D.... ? ?
0x081E.... ? ?
0x081F.... ? ?
0x0820.... ? ?

Config NVRAM service "cfg:nor"

Command Header Description
0x00010040 Initialize
0x00020000 Shutdown
0x00030040 (u8 flag) Writes the input flag to state. Uses SPI service command EnableSpiBus.
0x00040000 Writes the u8 from the state written by 0x00030040 to cmdreply[2].
0x00050082 ReadData
0x00060082 WriteData
0x00070000 This just uses the WREN command.
0x00080000 This just uses the WRDI command.
0x00090000 ReadIdentification
0x000A0000 This waits for the WIP bit in the status register to clear(wait for writing to finish).
0x000B0000 This waits for the WEL bit in the status register to become set(write enabled).
0x000C0000 This writes the value of the WIP bit in the status register to u8 cmdreply[2].
0x000D0000 This writes the value of the WIP bit in the status register to u8 cmdreply[2].
0x000E0000 ReadStatusRegister
0x000F0082 ReadDataOther
0x00100082 WriteDataOther
0x00110040 (u32 offset) Uses command WREN then waits for WEL to become enabled. Sends command 0xDB to SPI followed by the specified flash offset.
0x00120040 (u32 offset) Identical to 0x00110040 except this uses SPI-command 0xD8 instead("block erase").
0x00130000 This uses SPI command 0xB9 for "Deep power down".
0x00140000 This uses SPI command 0xAB for "Release from deep power down".

This is an interface for the "SPI::NOR" service, for accessing the Wifi NVRAM/SPI Flash.