1,434
edits
Changes
Jump to navigation
Jump to search
mLine 127:
Line 127: − + − + Line 148:
Line 148: − + Line 154:
Line 154: − + − + Line 187:
Line 187: − + Line 193:
Line 193: − + Line 241:
Line 241: − + − + − + − + − + − + Line 262:
Line 262: − +
→Trigger Command List Processing
|-
|-
| 7
| 7
| Flag: when source buffer is not located in VRAM and this flag is non-zero, svcFlushProcessDataCache is used with the source buffer.
| Flush source (0 = don't flush, 1 = flush)
|}
|}
This command is normally used to DMA data from the application GSP [[Memory_layout|heap]] to VRAM.
This command is normally used to DMA data from the application GSP [[Memory_layout|heap]] to VRAM. When flushing is enabled and the source buffer is not located within VRAM, svcFlushProcessDataCache is used to flush the source buffer.
== Trigger Command List Processing ==
== Trigger Command List Processing ==
|-
|-
| 3
| 3
| Flag, bit0 is written to GSP module state
| Update gas additive blend results (0 = don't update, 1 = update)
|-
|-
| 6-4
| 6-4
|-
|-
| 7
| 7
| When non-zero, call svcFlushProcessDataCache() with the specified buffer
| Flush buffer (0 = don't flush, 1 = flush)
|}
|}
This command converts the specified address to a physical address, then writes the physical address and size to the [[GPU]] registers at 0x1EF018E0. This buffer contains [[GPU_Commands|GPU commands]].
This command converts the specified address to a physical address, then writes the physical address and size to the [[GPU]] registers at 0x1EF018E0. This buffer contains [[GPU/Internal_Registers|GPU commands]]. When flushing is enabled, svcFlushProcessDataCache is used to flush the buffer.
== Trigger Memory Fill ==
== Trigger Memory Fill ==
|-
|-
| 7
| 7
| The low u16 is control0, while the high u16 is control1 (?)
| Control0 <nowiki>|</nowiki> (Control1 << 16)
|}
|}
The associated buffer address must not be <= to the main buffer address, thus the associated buffer address must not be zero as well. When the bufX address is zero, processing for the bufX parameters is skipped.
The associated buffer address must not be <= to the main buffer address, thus the associated buffer address must not be zero as well. When the bufX address is zero, processing for the bufX parameters is skipped.
The values of control0 and control1 give information about the type of memory fill. See [[GPU Registers#Memory Fill|here]] for more information about memory fill parameters.
The values of Control0 and Control1 give information about the type of memory fill. See [[GPU/External_Registers#Memory Fill|here]] for more information about memory fill parameters.
== Trigger Display Transfer ==
== Trigger Display Transfer ==
|-
|-
| 1
| 1
| Input buffer address
| Input buffer address.
|-
|-
| 2
| 2
| Output buffer address
| Output buffer address.
|-
|-
| 3
| 3
| Size
| Total bytes to copy, not including gaps.
|-
|-
| 4
| 4
| Input [[GPU|dimensions]]?
| Bits 0-15: Size of input line, in bytes. Bits 16-31: Gap between input lines, in bytes.
|-
|-
| 5
| 5
| Output dimensions?
| Same as 4, but for the output.
|-
|-
| 6
| 6
| Flags, normally this is 0x8, with bit2 optionally set when either of the dimensions fields are set.
| Flags, corresponding to the [[GPU/External_Registers#Transfer_Engine|Transfer Engine flags]]. However, for TextureCopy commands, bit 3 is always set, bit 2 is set if any output dimension is smaller than the input, and other bits are always 0.
|-
|-
| 7
| 7
|}
|}
This command is similar to cmd3. It also writes to the [[GPU]] registers at 0x1EF00C00. It's unknown where the difference is.
This command is similar to cmd3. It also triggers the [[GPU/External_Registers#Transfer_Engine|GPU Transfer Engine]], but setting the TextureCopy parameters.
== Flush Cache Regions ==
== Flush Cache Regions ==