215
edits
Changes
Jump to navigation
Jump to search
Line 227:
Line 227: + + + + + Line 319:
Line 324: − + − + − + − + − + − + Line 365:
Line 370: − + − + − + − + − + − + − + − + Line 407:
Line 412: − + − + + + Line 448:
Line 455: − + Line 458:
Line 465: − + Line 483:
Line 490: − + − + − + − + + + + + + + + + Line 505:
Line 520: − + Line 533:
Line 548: + − + − + + + + + + − + − + − + − + − + − + − + − + − + − + − + − + + Line 596:
Line 618: − + + − + +
→Device 3
== Device 3 ==
== Device 3 ==
ro = read-only (writing is no-op)
rw = read-write
wo = write-only (reading will yield 00, FF, or unpredictable data)
s* = shared register (explaination below this table)
*v = volatile (survives reboots)
{| class="wikitable" border="1"
{| class="wikitable" border="1"
! REGISTER
! REGISTER
| 0x15
| 0x15
| s
| s
| rw
| rw v
| ? (volatile;survives reboot and power off)
| ?
|-
|-
| 0x16
| 0x16
| s
| s
| rw
| rw v
| ? (volatile;survives reboot and power off)
| ?
|-
|-
| 0x17
| 0x17
| s
| s
| rw
| rw v
| ? (volatile;survives reboot and power off)
| ?
|-
|-
| 0x18
| 0x18
| 0x1C
| 0x1C
| s
| s
| rw
| rw v
| ? (volatile;survives reboot and power off)
| ?
|-
|-
| 0x1D
| 0x1D
| s
| s
| rw
| rw v
| ? (volatile;survives reboot and power off)
| ?
|-
|-
| 0x1E
| 0x1E
| s
| s
| rw
| rw v
| ? (volatile;survives reboot and power off)
| ?
|-
|-
| 0x1F
| 0x1F
| s
| s
| rw
| rw v
| ? (volatile;survives reboot and power off)
| ?
|-
|-
| 0x20
| 0x20
bit2: bottom screen backlight off
bit2: bottom screen backlight off
bit3: bottom screen backlight on
bit3: bottom screen backlight on
bit4: top screen backlight off (does nothing on 2DS as the backlight is bottom only)
bit4: top screen backlight off
bit5: top screen backlight on (see above)
bit5: top screen backlight on
bits 4 and 5 have no effect on a 2DS because the backlight source is the bottom screen
|-
|-
| 0x23
| 0x23
| s
| s
| rw
| rw
| WiFi LED state, non-0 value turns on the WiFi LED, capped at 0x0F
| WiFi LED state, non-0 value turns on the WiFi LED, 4 bits wide
|-
|-
| 0x2B
| 0x2B
| s
| s
| rw
| rw
| 3D LED state, capped at 0x0F
| 3D LED state, 4 bits wide
|-
|-
| 0x2D
| 0x2D
byte 1: minutes
byte 1: minutes
byte 2: hours
byte 2: hours
byte 3: current day of the week (unused)
byte 3: current week (unused)
byte 4: days
byte 4: days
byte 5: months
byte 5: months
byte 6: years
byte 6: years
byte 7: leap year counter (unused)
byte 7: leap year counter / "watch error correction" register (unused)
|-
|-
| 0x38
| 0x38
- 0x3C
- 0x3A
| s
| s
| rw
| rw
| RTC alarm registers
| RTC alarm registers
Register 0x3B could be used to upload [[MCU_Services#MCU_firmware_versions|MCU firmware]] if some conditions are met.
byte 0: minutes
byte 1: hours
byte 2: week
|-
| 0x3B
- 0x3D
| s
| rw
| Register 0x3B could be used to upload [[MCU_Services#MCU_firmware_versions|MCU firmware]] if some conditions are met.
|-
|-
| 0x3D
| 0x3D
| s
| s
| wo
| wo
| Peripheral power related? bit0 seems to depower everything, pressing the power key afterwards instantly turns the whole 3DS off
| Register-mapped MCU RESET?
|-
|-
| 0x40
| 0x40
|-
|-
| 0x45
| 0x45
- 0x4A
| s
| s
| rw
| ro
| ?
| Gyroscope 3D rotation from the 12bit ADC, left shifted 4 to fit in a 16bit signed short
{| class="wikitable" border="1"
! AXIS
! V=0x00
! V=0x40
! V=0xC0
|-
|-
| 0x46
| Y (=roll)
| s
| held vertically
| ro
| vertical right side
| Gyro Y(?) axis rotation (0x00 = flat, 0x40 = 3DS standing on right side, 0xBE = 3DS standing on left side)
| vertical left side
|-
|-
| 0x48
| Z? (=yaw)
| s
| ???
| ro
| ???
| Gyro Z(?) axis rotation (0x00 = flat, 0x40 = 3DS standing horizontally, 0xBE = 3DS base is horizontally upside-down)
| ???
|-
|-
| 0x4A
| X? (=pitch)
| s
| held vertically
| ro
| ???
| Gyro X(?) axis rotation (0x00 = 3DS base facing upwards, 0x40 = face-down flat, 0xBE = standing(?) flat)
| ???
|}
|-
|-
| 0x4B
| 0x4B
| s
| s
| rw
| rw
| DSP volume slider 0% volume offset (setting this to 0xFF will esentially mute the DSP as it's the volume slider's maximum raw value)
| Register-mapped ADC register
DSP volume slider 0% volume offset (setting this to 0xFF will esentially mute the DSP as it's the volume slider's maximum raw value)
|-
|-
| 0x59
| 0x59
| s
| s
| rw
| rw
| DSP volume slider 100% volume offset (setting both this and the above to 0 will disable the volume slider with 100% volume, setting this to a lower value than the above will make the volume slider have only 2 states; on and off)
| Register-mapped ADC register
DSP volume slider 100% volume offset (setting both this and the above to 0 will disable the volume slider with 100% volume, setting this to a lower value than the above will make the volume slider have only 2 states; on and off)
|-
|-
| 0x5A
| 0x5A