Difference between revisions of "I2C Registers"

From 3dbrew
Jump to navigation Jump to search
Line 224: Line 224:
 
| 0xa0
 
| 0xa0
 
| "i2c::EEP"
 
| "i2c::EEP"
| eeprom?
+
| HWCAL EEPROM ([[Hardware_calibration#Header|only present on dev units where SHA256 is used for HWCAL verification]])
 
|-
 
|-
 
| 15
 
| 15

Revision as of 17:38, 2 May 2019

Registers

Old3DS Name Address Width Used by
Yes I2C1_DATA 0x10161000 1 I2C bus 1 devices
Yes I2C1_CNT 0x10161001 1 I2C bus 1 devices
Yes I2C1_CNTEX 0x10161002 2 I2C bus 1 devices
Yes I2C1_SCL 0x10161004 2 I2C bus 1 devices
Yes I2C2_DATA 0x10144000 1 I2C bus 2 devices
Yes I2C2_CNT 0x10144001 1 I2C bus 2 devices
Yes I2C2_CNTEX 0x10144002 2 I2C bus 2 devices
Yes I2C2_SCL 0x10144004 2 I2C bus 2 devices
Yes I2C3_DATA 0x10148000 1 I2C bus 3 devices
Yes I2C3_CNT 0x10148001 1 I2C bus 3 devices
Yes I2C3_CNTEX 0x10148002 2 I2C bus 3 devices
Yes I2C3_SCL 0x10148004 2 I2C bus 3 devices

I2C_CNT

BIT DESCRIPTION
0 Stop (0=No, 1=Stop/last byte)
1 Start (0=No, 1=Start/first byte)
2 Pause (0=Transfer Data, 1=Pause after Error, used with/after Stop)
4 Ack Flag (0=Error, 1=Okay) (For DataRead: W, for DataWrite: R)
5 Data Direction (0=Write, 1=Read)
6 Interrupt Enable (0=Disable, 1=Enable)
7 Start/busy (0=Ready, 1=Start/busy)

I2C_CNTEX

BIT DESCRIPTION
0-1 ? Set to 2 normally.

I2C_SCL

BIT DESCRIPTION
0-5 ?
8-12 ? Set to 5 normally.

I2C Devices

Device id Device bus id Device Write Address Accessible via I2C service Device description
0 1 0x4a "i2c::MCU" Power management?(same device addr as the DSi power-management)
1 1 0x7a "i2c::CAM" Camera0?(same dev-addr as DSi cam0)
2 1 0x78 "i2c::CAM" Camera1?(same dev-addr as DSi cam1)
3 2 0x4a "i2c::MCU" MCU
4 2 0x78 "i2c::CAM" ?
5 2 0x2c "i2c::LCD" ?
6 2 0x2e "i2c::LCD" ?
7 2 0x40 "i2c::DEB" ?
8 2 0x44 "i2c::DEB" ?
9 3 0xa6 "i2c::HID" Unknown. The device table in I2C-module had the device address changed from 0xA6 to 0xD6 with 8.0.0-18.
10 3 0xd0 "i2c::HID" Gyroscope
11 3 0xd2 "i2c::HID" ?
12 3 0xa4 "i2c::HID" DebugPad
13 3 0x9a "i2c::IR" IR
14 3 0xa0 "i2c::EEP" HWCAL EEPROM (only present on dev units where SHA256 is used for HWCAL verification)
15 2 0xee "i2c::NFC" New3DS-only NFC
16 1 0x40 "i2c::QTM" New3DS-only QTM
17 3 0x54 "i2c::IR" Used by IR-module starting with 8.0.0-18, for New3DS-only HID via "ir:rst". This deviceid doesn't seem to be supported by i2c module on 8.0.0-18(actual support was later added in New3DS i2c module).

Notice: These device addresses are used for writing to the respective device, for reading bit0 must be set (see I2C protocol). Thus, the actual device address is >> 1.

Device 3

 ro = read-only (writing is no-op)
 rw = read-write
 wo = write-only (reading will yield 00, FF, or unpredictable data)
 d* = dynamic register (explaination below this table)
 s* = shared register (explaination below this table)
 ds = dynamic shared (explaination below this table)
REGISTER WIDTH INFO DESCRIPTION
0x00 s ro Version high
0x01 s ro Version low
0x02 d rw 2bit value, writing will mask away/"acknowledge" the event, set to 3 by mcuMainLoop on reset if reset source is Watchdog
 bit0: RTC clock value got reset to defaults
 bit1: Watchdog reset happened
0x03 ds rw Top screen flicker
0x04 ds rw Bottom screen flicker
0x05

- 0x07

s rw Danger zone - MCU unlock sequence is written here.
0x08 s ro Raw 3D slider position
0x09 s ro Volume slider state (0x00 - 0x3F)

This is the same value returned by MCUHWC:GetSoundVolume

0x0A s ro ? (seems to be power management related?)
0x0B s ro Battery percentage
0x0C s ro ? (changes to 0 for a second when the charger is plugged in then it resets to its previous value)
0x0D s ro System voltage
0x0E s ro ?
0x0F s ro Flags: bit7-5 are read via mcu::GPU. The rest of these are read via mcu::RTC: bit4 = BatteryChargeState. bit3 = AdapterState. bit1 = ShellState.
0x10

- 0x13

s ro Received interrupt bitmask, see register 0x18 for possible values

If no interrupt was received this register is 0

0x14 s ro Unused and unwritable byte :(
0x15

- 0x17

s rw Unused and unreferenced free RAM! Good for userdata.
0x18

- 0x1B

s rw Interrupt mask for register 0x10 (0=enabled,1=disabled)
 bit00: Power button press (for 27 "ticks")
 bit01: Power button held (for 375 "ticks"; the 3DS turns off regardless after a fixed time)
 bit02: HOME button press (for 5 "ticks")
 bit03: HOME button release
 bit04: WiFi switch button
 bit05: Shell close
 bit06: Shell open
 bit07: Fatal hardware condition(?) (sent when the MCU gets reset by the Watchdog timer)
 bit08: Charger removed
 bit09: Charger plugged in
 bit10: RTC alarm (when some conditions are met it's sent when the current day and month and year matches the current RTC time)
 bit11: ??? (accelerometer related)
 bit12: HID update
 bit13: Battery dead(?)
 bit14: Battery stopped charging (independent of charger state)
 bit15: Battery started charging

Nonmaskable(?) interrupts

 bit16: ???
 bit17: ??? (opposite even for bit16)
 bit22: Volume slider position change
 bit23: ??? Register 0x0E update
 bit24: ??? (the off event for below bit)
 bit25: ??? (triggered when something related to the GPU is turned on)
 bit26: ??? (???)
 bit27: ??? (???)
 bit28: ??? (???)
 bit29: Battery percentage status change (triggered at 10%, 5%, and 0% while discharging)
 bit30: bit set by mcu sysmodule
 bit31: bit set by mcu sysmodule
0x1C

- 0x1F

s rw Unused and unreferenced free RAM! Good for userdata.
0x20 d wo System power control:
 bit0: power off
 bit1: reboot (unused?)
 bit2: reboot (used by mcu sysmodule and LgyBg)
 bit3: used by LgyBg to power off, causes hangs in 3DS-mode
 bit4: an mcu::RTC command uses this, seems to do something with the watchdog

Bit 4 sets a bit at a RAM address which seems to control the watcdog timer state, then this bit is immediately unmasked. This field has a bitmask of 0x0F.

0x21 d wo ??? switches up input bits from 0123456-- to 12-0435- then writes them to REG[0x5D] (0xFFC02)
0x22 d wo Used to set LCD states
 bit0: don't push to LCDs
 bit1: push to LCDs
 bit2: bottom screen backlight off
 bit3: bottom screen backlight on
 bit4: top screen backlight off
 bit5: top screen backlight on

Bits 4 and 5 have no effect on a 2DS because the backlight source is the bottom screen. The rest of the bits are masked away.

0x23 ?? wo ??? Seems to be stubbed, just returns the written value from the write handler function.
0x24 s rw Watchdog timer. This must be set *before* the timer is triggered, otherwise the old value is used. Value zero disables the watchdog.
0x25 s rw ?
0x26 s rw ?
0x27 sd rw Raw volume slider state
0x28 s rw Brightness of the WiFi/Power LED
0x29 sd(5) rw Power LED state + some extra data
0x2A s rw WiFi LED state, non-0 value turns on the WiFi LED, 4 bits wide
0x2B s rw Camera LED state, 4bits wide,
 0, 3, 6-0xF = off
 1 = slowly blinking
 2 = constantly on
 4 = flash once
 5 = delay before changing to 2
0x2C s rw 3D LED state, 4 bits wide
0x2D 0x64 wo This is used for controlling the notification LED (see MCURTC:SetInfoLEDPatternHeader as well), when this register is written. It's possible to write data here with size less than 0x64, and only that portion of the pattern data will get overwritten. Reading from this register only returns zeroes, so it's considered write-only. Writing past the size of this register seems to do nothing.
0x2E s ro This returns the notification LED status when read (1 means new cycle started)
0x2F s wo? ??? The write function for this register is stubbed.
0x30

- 0x36

ds rw RTC time (system clock). 7 bytes are read from this. The upper nibble of each byte encodes 10s (BCD), so each byte is post-processed with (byte & 0xF) + (10 * (byte >> 4)).
 byte 0: seconds
 byte 1: minutes
 byte 2: hours
 byte 3: current week (unused)
 byte 4: days
 byte 5: months
 byte 6: years
0x37 s rw RTC time byte 7: leap year counter / "watch error correction" register (unused in code)
0x38

- 0x3C

s rw RTC alarm registers
 byte 0: minutes(???)
 byte 1: hours(???)
 byte 2: day
 byte 3: month
 byte 4: year
0x3B s rw Could be used on very old MCU_FIRM versions to upload MCU firmware if some conditions are met.
0x3D

0x3E

ds ro RTC tick counter / "ITMC" (when resets to 0 the seconds increase)

Only reading 0x3D will update the in-RAM value

0x3F s wo 2 bits
 bit0: turns off P00 and sets it to output mode (seems to kill the entire SoC)
 bit1: turns on a prohibited bit in an RTC Control register and turns P12 into an output
0x40 s rw Pedometer state (?)
0x41 s rw Index selector for register 0x44
0x42 s rw Unused?
0x43 s rw Unused???, accelometer related
0x44 s rw ???, accelometer related
0x45

- 0x4A

s ro Gyroscope 3D rotation from the 12bit ADC, left shifted 4 to fit in a 16bit signed short
AXIS V=0x00 V=0x40 V=0xC0
Y (=roll) held vertically vertical right side vertical left side
Z? (=yaw) ??? ??? ???
X? (=pitch) held vertically ??? ???
0x4B s rw PedometerStepCount (for the current day)
0x4C

0x4D

?? ?? ??
0x4E d rw ??? this = (0xFFE9E & 1) ? 0x10 : 0
0x4F d(6) ro
0x50 s rw ???
0x51 s rw ???
0x52

- 0x57

s rw ?
0x58 s rw Register-mapped ADC register

DSP volume slider 0% volume offset (setting this to 0xFF will esentially mute the DSP as it's the volume slider's maximum raw value)

0x59 s rw Register-mapped ADC register

DSP volume slider 100% volume offset (setting both this and the above to 0 will disable the volume slider with 100% volume, setting this to a lower value than the above will make the volume slider have only 2 states; on and off)

0x5A s ro/rw Invalid, do not use! On newer MCU_FIRM versions this is unused, but on older MCU_FIRM versions this is a read-only counter.
0x5B

- 0x5F

s - These registers are out of bounds (0xFFC00 and up), they don't exist, writing is no-op, reading will yield FFs.
0x60 ds rw Looping queue register

Writing to first byte resets the queue position to the nth element Reading from this register causes the values to shift up by `readsize-1`(needs confirmation) bytes after returning `readsize-1` bytes from the top of the stack (first byte is read-only, so is always zero)

0x61 ds(0x100) rw Writing to this register pushes values on top of register 0x60's stack. Reading from this register doesn't advance the stack.

The first byte is used to store flags for managing FIRM/NS state - bit0 = "WirelessDisabled", bit1 = "SoftwareClosed", bit2 = "PowerOffInitiated", bit4 = "LegacyJumpProhibited". This register survives a power-off, but it resides in RAM, so its contents get lost on battery pulls. This register doesn't seem to actually control MCU behaviour by itself, it just seems to be used for storing arbitrary data.

0x62 - 0x7E s - These registers don't exist, writing is no-op, reading will yield FFs.
0x7F d(9-0x13) ro Various system state information.
 byte 0x06: battery related? (seems to decrease while charging and increase while discharging)
 byte 0x09: system model (see Cfg:GetSystemModel for values)
 byte 0x0A: power LED related? 0 is off, 1 is red
 byte 0x0D: RGB LED red intensity
 byte 0x0E: RGB LED green intensity
 byte 0x0F: RGB LED blue intensity
 byte 0x11: WiFi LED brightness
 byte 0x12: raw button states?
   bit0: unset while power button is held
   bit1: unset while home button is held
   bit2: unset while Wifi slider is held
   bit5: unset while the charging LED is active
   bit6: unset while charger is plugged in
   
   this byte is reset to 0 before an svcBreak takes effect

On MCU_FIRM major version 1 the size of this is 9, reading past the 9th byte will yield AA instead of FF.

0x80

- 0xFF

s - These registers don't exist, writing is no-op, reading will yield FFs.

Shared register: the letter "s" means that the given register is in a "shared register pool", meaning the resgister is in the register pool in RAM at address 0xFFBA4 + registernumber.

Dynamic register: these registers aren't in the shared pool, they just "pretend" to be there. These registers often don't retain their set value, change rapidly, or control various hardware.

Non-shared (dynamic) register: it's a register whose contents separate from the shared register pool. Messing with these registers will not affect the shared register pool at all.

On old versions of MCU_FIRM none of the invalid registers are masked away by the read handler function, but are still read-only. Newer MCU_FIRM versions return the hardcoded value FF instead.

Device 5 & 6

LCD controllers for main/sub displays, most likely.

Register Width Name Description
0x1 8 ?
0x11 8 ?
0x40 8 CMD_IN/CMD_RESULT1 Write to trigger a command? Seen commands: 0xFF=Reset?, 0x62=IsFinished?. Result is stored in CMD_RESULT1:CMD_RESULT0.
0x41 8 CMD_RESULT0 Read result
0x50 8 ?
0x60 8 ?
0xFE 8 ?

Device 10

See the datasheet linked to on the Hardware page for reference.

Device 12

REGISTER WIDTH DESCRIPTION
0x0 21 DebugPad state.

This is the DebugPad device, see here.

Device 13

Raw I2C register address Internal register address Width Description
0x0 0x0 0x40 RHR / THR (data receive/send FIFO)
0x8 0x1 0x1 IER
0x10 0x2 0x1 FCR/IIR
0x18 0x3 0x1 LCR
0x20 0x4 0x1 MCR
0x28 0x5 0x1 LSR
0x30 0x6 0x1 MSR/TCR
0x38 0x7 0x1 SPR/TLR
0x40 0x8 0x1 TXLVL
0x48 0x9 0x1 RXLVL
0x50 0xA 0x1 IODir
0x58 0xB 0x1 IOState
0x60 0xC 0x1 IoIntEna
0x68 0xD 0x1 reserved
0x70 0xE 0x1 IOControl
0x78 0xF 0x1 EFCR

See the datasheet linked to on the Hardware page for reference. From that datasheet, for the structure of the I2C register address u8: "Bit 0 is not used, bits 2:1 select the channel, bits 6:3 select one of the UART internal registers. Bit 7 is not used with the I2C-bus interface, but it is used by the SPI interface to indicate a read or a write operation."

Device 14

Used by Cfg-sysmodule via the i2c::EEP service. This is presumably EEPROM going by the service name.

The Cfg-module code which loads the CCAL(nandro:/sys/{HWCAL0.dat/HWCAL1.dat}) file from NAND will load it from I2C instead, if a certain state flag is non-zero. Likewise for the function which writes CCAL to NAND. HMAC/hash verification after loading is skipped when the CCAL was loaded from I2C.

Device 15

This the New3DS NFC controller "I2C" interface. This device is accessed via the WriteDeviceRaw/ReadDeviceRaw I2C service commands.

Since the *Raw commands are used with this, this device has no I2C registers. Instead, raw data is transfered after the I2C device is selected. Hence, WriteDeviceRaw is used for sending commands to the controller, while ReadDeviceRaw is for receiving responses from the controller. Certain commands may return multiple command responses.

Command request / response structure:

Offset Size Description
0x0 0x1 Normally 0x10?
0x1 0x1 Command source / destination.
0x2 0x1 CmdID
0x3 0x1 Payload size.

Following the above header is the payload data(when payload size is non-zero), with the size specified in the header. The command response payload is usually at least 1-byte, where that byte appears to be normally 0x0. For command requests the payload data is the command parameters.

For command requests sent to the NFC tag itself, Cmd[1]=0x0 and CmdID=0x0. The command request payload data here is the actual command request data for the NFC tag, starting with the CmdID u8 at payload+0.

During NFC module startup, a certain command is sent to the controller which eventually(after various cmd-reply headers etc) returns the following the payload after the first byte in the payload:

000000: 44 65 63 20 32 32 20 32 30 31 32 31 34 3a 35 33  Dec 22 201214:53 
000010: 3a 35 30 01 05 0d 46 05 1b 79 20 07 32 30 37 39  :50...F..y .2079
000020: 31 42 35                                         1B5

Or that is: "Dec 22 201214:53:50<binary>20791B5". Therefore, this appears to return the part-number of the NFC controller(other command request(s) / response(s) use this part-number value too).

NFC controller commands

CmdRequest[1] CmdID Payload data for parameters Description
0x2E 0x2F Firmware image for this chunk, size varies. This is used during NFC module startup to upload the firmware image to the NFC controller. This is used repeatedly to upload multiple chunks of the image.